Then you can run the software to test it.
Then sent the ‘ RenOLink‘ icon to desktop as shortcut.Īfter all these steps, you can connect the Renolink OBD2 Interface to laptop, the device USB driver will be installed automatically. Now, you need to click the Window START button on your desktop at low-left corner to right-click the ‘ RenOLink‘ icon, and then select ‘ Properties‘Ĭopy ‘ renolink.dat‘ and ‘ RenOLink‘ to replace the same on the RenOLink folder you opened just now, see pictures below Please wait while Setup installs RenOlink on your computer, then click ‘ Finish‘ If you would like to select a different folder, then click ‘ Browse‘Ĭlick ‘ Install‘ to continue with the installation. Now please click ‘ renolink_setup3‘ to open Then select ‘ I accept this agreement‘, and click ‘ Next‘Īfter Device Driver installation Wizard completing installation, then you can click ‘ Finish‘ It will show the Device Driver Installation Wizard, then click ‘ Next‘ to continue Now back to the software file folder, then double click ‘ CDM21218_Setup_720‘
Then it will install Microsoft.NET Framework 4 automaticallyĪfter installation completing, then click ‘ Finish‘ Tick ‘ I have read and accept the license terms‘, and then click ‘ Install‘ to continue Now it will setup ‘Microsoft.NET Framework 4’ Here we also share the Renolink OBD2 Renault ECU programmer software installation guide in win 7 for your reference:įirst open OBDlink SX software CD to get into Renolink OBD2 software folder
You can do following with Renolink programming device: Renolink OBD2 Renault ECU Programmer Software Free Download VXDAS.COM share the Renolink download link of V1.52. Renolink supports key programming, ECU and airbag reset, EEPROM read/write etc.
It is recommended to install on your PC the ECM Titanium Management Tool software,whichĪllows you to run ECM Titanium without using the AutoPlay window or Window Explorer every time. If ECM Titanium doesn’t start up,please contact your dealer in order to solve the problem. In this phase it is recommended that the PC is connected to the Internet.Īfter updating, it finally appears the main window of ECM Titanium software ready to be used.
When ECM Titanium Upgrade Program window is open, the software tries to connect to the Internet Databank to look for any updates and download the list of the available Drivers. Search the file ECM_Titanium.bat and run it.Īfter completing these steps, ECM Titanium Upgrade Program Window will pop up.Plug the flash drive into a USB port on your computer.To run ECM Titanium software, just follow these four steps: In this case, you must repeat the installation of the USB driver as described in the document ECM_Quickstart_ENU.pdf. To run ECM Titanium software it is necessary to use a computer running Window Vista or 7 that has a free USB port.įollowing the procedure written in the document ECM_Quickstart_ENU.pdf (located in the sameĮCM Titanium USB flash drive, Picodisk), the operating system of the computer will install the suitable USB driver used to operate the flash drive.įrom this point on, you no longer need to repeat this procedure,unless you want to use the program on another computer. Part3:Original ECM Titanium Installation Guide: Select “Werkzeuge->Sprachauswhl” to do language setup. Right click “ECM Titanium Alientech S.r.l.” to sent to Desktop. Open “My computeràECM Titanium (E:)” to copy the folder “ECM FULL” to “My computeràLocal Disk (C:). Part2:Crack ECM Titanium Installation Guide:(Have not Tested yet) Now ECM Titanium with 26106 will work correctly Paste “DataBase” folder to C:\garageforumECM4free It will take about 10 minutes to complete,please waitĪfter then go to C:\garageforumECM4free,and delete “DataBase” folderĬopy “DataBase” folder on your extract folder Now it will start to install ECM Titanium,click “Next” Then it will ask you where would you like the shortcuts to be installed,click “Next” to continue “C:/garageforumECM4free” into “C:\garageforumECM4free”,click “Next”